Skip to content

How to Check and Replace Bike Brake Pads

Rim and disc brakes, step by step.

By Medell. Editorial2 min read
Close-up of a bicycle front brake
Anton Savinov / Unsplash

Before you start

Difficulty
Beginner
Estimated time
20 min

Tools required

  • •Hex keys (usually 2–5 mm)
  • •Small flat screwdriver or pad spreader
  • •Replacement pads matched to your brake model
  • •Isopropyl alcohol and a clean rag

Safety

  • •Use pads made for your exact brake model.
  • •Never touch disc rotors or pads with oily fingers.
  • •Test brakes at walking speed before riding.

Brake pads wear every time you stop. Checking them takes a minute; replacing them takes less than half an hour and needs only basic tools.

How to tell your pads are worn

  • Rim brakes: most pads have wear-indicator grooves. When the grooves are gone, replace the pads.
  • Disc brakes: look into the caliper. Replace pads when the friction material is about as thin as the manufacturer's limit, often around 0.5 mm.
  • A grinding, metal-on-metal sound means the pads are already past their limit.

Replacing rim brake pads

  1. 01

    Loosen the pad bolt

    Loosen the bolt holding the pad holder to the brake arm and remove the old pad or insert.

  2. 02

    Fit the new pad

    Install the new pad, noting any arrow that shows the direction of wheel rotation.

  3. 03

    Align it to the rim

    Position the pad so it hits the braking surface squarely, not the tire, with the front edge touching very slightly first.

  4. 04

    Tighten and test

    Tighten the bolt firmly, then squeeze the lever and check both pads meet the rim at the same time.

Replacing disc brake pads

  1. 01

    Remove the wheel

    Take the wheel out so you can see into the caliper.

  2. 02

    Remove the retaining pin

    Undo the pad retaining pin or bolt and slide the old pads out.

  3. 03

    Push the pistons back

    Gently push the pistons back into the caliper with a plastic tire lever or pad spreader. Avoid metal tools on the pistons.

  4. 04

    Install new pads

    Fit the new pads and spring, refit the retaining pin and secure it.

  5. 05

    Bed in the pads

    Refit the wheel, pump the lever a few times, then do several controlled stops from moderate speed to bed in the pads.

Frequently asked questions

Should I choose resin or metallic disc pads?

Resin (organic) pads are usually quieter with good initial bite but wear faster, especially in wet, gritty conditions. Metallic (sintered) pads last longer and handle heat better but can be noisier. Check which types your brake supports.

Do I need to bed in new pads?

Yes. Bedding in transfers a thin layer of pad material to the rotor and gives full braking power. Do a series of controlled stops from moderate speed before riding normally.

Up next · 2 min readHydraulic Disc Brakes: Bleed or New Pads? →

The Medell. Letter

New rides, workshop guides and reviews, in your inbox.

Free. Every two weeks, never daily. One-click unsubscribe. See our privacy policy.

Brakes

Hydraulic Disc Brakes: Bleed or New Pads?

Spongy lever, squealing, or fading power? Each symptom points to a different fix. A troubleshooting guide for hydraulic disc brakes.

Intermediate45 min job
Brakes

How to Adjust Mechanical Disc Brakes

Cable-operated disc brakes need regular adjustment as pads wear. How to centre the caliper, set pad clearance and tune cable tension.

Intermediate20 min job
Troubleshooting

The 2-Minute Pre-Ride Bike Safety Check

Air, brakes, chain, quick releases and a final look-over. A simple pre-ride routine that catches most problems before they leave you stranded.

Beginner2 min job

The Medell. Letter · Free

Free. Every two weeks, never daily. One-click unsubscribe. See our privacy policy.

  1. 01One workshop fixA repair you can do this weekend, with tools and time listed.
  2. 02One road worth ridingRoutes and rides from around the islands.
  3. 03Gear notes, honestly labelledHands-on or research-based, always said up front.